S355 is a structural micro alloyed grade used for a great variety of applications. It is standardized with a specified impact strength of 27 J at a few different temperatures, but EN10027 gives guidelines how to extend the designation. Similar designations. S355K2 15Mn4, S355JR C16, S355J2 C16
St52 Steel Properties Physical Properties. Material St 52 3 Density7.85 g/cm3; Melting point1420 1460 °C (2590 2660 °F) Mechanical Properties. The datasheet below shows St52 steel yield strength, tensile strength, elongation and impact resistance. Structural Steel St52 3 Hardness180 HB, annealed[plate]Steel Hardness Conversion Table Calculator West [steel]Steel hardness conversion table containing conversion factors for Rockwell, Vickers & Brinell. As a guide we show the theoretical conversion comparison of tonnes tensile in Newtons/mm² and MPa to steel hardness. N/mm² / MPa. Brinell HB. Tons per sq in. Vickers. Rockwell C. Rockwell B.[plate]Force AnalysisContact StressAllowable, Permitted [steel]SteelsHardness and Allowable Stress. The table below from ISO 6336 Part 5 shows a 'first estimation' of the Allowable Contact Stress, for 5x10 7 cycles for different classes of steel and surface treatments, or for nitriding steels, 2×10 6 cycles. The reliability is taken as 99%.
Non alloyed steel which, in essentially round and sheet formats, has a wide range of applications, mainly in welded construction. Hardness Rm Rp0,2 Hardness HB . Hardness HRC . [plate]Hardox 450 The most popular structural wear plate SSAB[steel]Hardox® 450 is an abrasion resistant steel with a nominal hardness of 450 HBW. Hardox® 450 combines good bendability and weldability with an option for guaranteed impact toughness (Hardox® 450 Tuf). The products can be used in many different components and structures that are subject to wear. Hardox® 450, with an extra 50 Brinell hardness [plate]EN36A Case Hardening Steel Interlloy Engineering [steel]*Annealed Brinell HardnessMax255NoteMechanical tests are in the blank carburised condition Hardening Temperature 800 o C 820 o C *Hardness figures are in the condition stated. Typical Mechanical Properties AnnealedTensile Strength Mpa700/770Yield Strength Mpa540Elongation on 5.65S 0 % 25HardnessHB212Rc17
Hardox® 450 is an abrasion resistant steel with a nominal hardness of 450 HBW. Hardox® 450 combines good bendability and weldability with an option for guaranteed impact toughness (Hardox® 450 Tuf). The products can be used in many different components and structures that are subject to wear. Hardox® 450, with an extra 50 Brinell hardness [plate]EN36A Case Hardening Steel Interlloy Engineering [steel]*Annealed Brinell HardnessMax255NoteMechanical tests are in the blank carburised condition Hardening Temperature 800 o C 820 o C *Hardness figures are in the condition stated. Typical Mechanical Properties AnnealedTensile Strength Mpa700/770Yield Strength Mpa540Elongation on 5.65S 0 % 25HardnessHB212Rc17[plate]ABRAMS STEEL GUIDE[steel]AISI/SAE 1.0570 (St 52 3)Unalloyed structural steel with good machinability and dimensional stability, high toughness and good weldability because of its low carbon content (C = 0,22 %). This grade is only used for unhardened components. Working hardnessapprox. 180 HB (annealed).Applications:
Hardness. It refers to the ability of the material to resist hard pressing into its surface. There are three types of hardnessBrinell hardness, Rockwell hardness and Vickers hardness. Generally, the hardness of steel increases with the increase of carbon content in steel. Brinell HardnessHB[plate]S460 Steel EN10025 3 S460n Brown McFarlane[steel]There are four grades of EN10025:3 steel plate, (S275, S355, S420 and S460) these indicate each grades minimum yield strength (in MPa) for plates 16 mm thick and below. Each grade is further sub divided based on the specified minimum value of impact energy at a particular temperature. N indicates temperatures not lower than 20 deg C and NL [plate]S460 Steel EN10025 3 S460n Brown McFarlane[steel]There are four grades of EN10025:3 steel plate, (S275, S355, S420 and S460) these indicate each grades minimum yield strength (in MPa) for plates 16 mm thick and below. Each grade is further sub divided based on the specified minimum value of impact energy at a particular temperature. N indicates temperatures not lower than 20 deg C and NL
The Vickers hardness has the same basic principle as with all common measures of hardness, is to observe the questioned material's ability to resist plastic deformation from a standard source. According to our experience, as for the iron and steel castings, the Brinell hardness is more common in China.[plate]Q345 datasheet, Q345 property, Q345 Steel Grades[steel]Haihong International Trade (HK) CO., Limited. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. Q345 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. TEL:+86 816 FAX+86 816 2[plate]Hardox 500 Wear resistant steel with extra high [steel]The bendable, weldable and highly abrasion resistant steel. Hardox® 500 is a bendable and weldable abrasion resistant steel, with a nominal hardness of 500 HBW. Suitable for applications that demand higher wear resistance. Hardox® 500 increases payload and increases service life while maintaining good processability and toughness.
Steel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 [plate]
Our Steel Products' Certificates:
Our Factory:
Packaging & shipping: